4 100mm Plastic Round Ducting Ventilation Tube Extractor Fan Vent Pipe fittings

  
Add all items to the basket to receive the discount. Add to your watch list. 350mm long 100mm Ducting Tube. Primarily used as a wall sleeve for the installation of an individual extracting installation. Fits over male spigots of 100mm ducting fittings. Long lasting compared to flexible hose that can wear against abrasive masonary. Colour: White Free Area: 7,855mm² Max/min temp: 60°C / -15°C Material(s) used: PVCu. Telescopic Wall Sleeve with Reducing Ring. Being telescopic it can be adjusted in length to fit the wall thickness. Add to your watched items to easily find again. Don't forget the fixing clips. Pipe fixing Clip 100mm Round. Supplied in two parts with the top section used to secure the clip via the pre-determined screw fixing position. The 100mm rigid pipe is then secured using the bottom section's clip in mechanism. Manufactured in compliance with Domestic Plastic ductwork Specification DW/154 and does meet UL94HB flammability standard. Colour: White Max/min temp: 60°C / -15°C Material(s) used: Polypropylene.

45 deg Elbow Bend 100mm Round. Fits into Ø 100mm ducting tube. Colour: White Free Area: 7,283mm² Max/min temp: 60°C / -15°C Material(s) used: High Impact Polystyrene. 90 deg Elbow Bend 100mm Round.

Used to connect Ø 100mm ducting tubes together, flexible hoses together using worm drive clips or connecting rigid to flexible ducting. Pipe connector with damper 100mm Round. Placed in the ducting system to direct airflow. Suitable for splitting a 100mm ducting run at 45° in either direction. Compliant with Part F of the Building Regulations. Suitable for commercial and domestic use. Consider dampers to control airflow! The wall plate is designed for use where existing ducting connections or fans have been installed in a wall and a decorative cover or new fixing method is needed. Prefer one with built in connector?

Wall Plate with Damper 100mm Round. This wall plate includes a pipe connector with damper. It is formed all in one piece and helps clamp the wall sleeve between the exterior wall terminal and itself. The damper raises to allow air to be expelled and closes with any backdraught to help prevent air returning in to the duct system, The damper can be removed if it is not needed. Condensation trap with over flow.

The condensation trap is installed at the lowest point in vertical rises where condensate can accumulate. An internal gutter within the trap collects the condensate running down the duct and then drains it to the outside through a standard overflow 22mm pipe connector. Used to connect spiral flexible ducting hose to rigid ducting systems. The male fitting fits into 100mm ducting tube.

A hose for this item is available on this listing! Used to connect spiral flexible ducting hose to rigid ducting systems, The female fitting has the same diameter as 100mm rigid ducting tube. It will fit onto male fittings such as elbows. But not onto duct tube without a connector. Need one to fit ducting tube see male version.

Doesn't fit 100mm duct. 100mm - 80mm hose end reducer. Colour: White Max/min temp: 60°C / -15°C Material(s) used: High Impact Polystyrene. Same diameter as 125mm ducting tube and fits into 100mm ducting tube. Don't forget your sealant or sealing tape! Same Ø as 125mm duct tube. 150mm end is the same diameter as 150mm ducting tube. The 10omm end fits inside 100mm ducting. Male 100mm to 110 x 54mm Adapter. Designed to connect round and rectangular ducting systems together. Fits into Ø 100mm ducting tube and over 110 x 54mm ducting tube. Colour: White Free Area: Round end: 7,283mm² Rect end: 5,424mm² Max/min temp: 60°C / -15°C Material(s) used: High Impact Polystyrene. See offset version if you need to lay tubes on flat surfaces such as on top of kitchen units. Female 100mm to 110 x 54mm Adapter. Designed to connect round fittings such as elbows, cowls etc to rectangular ducting systems.

Same diameter as 100mm ducting tube and fits over 110 x 54mm ducting tube. See offset version if you need to lay tubes on flat surface such as on top of kitchen units. Doesn't fit 100mm Duct. Designed to connect round and rectangular ducting together. Will need a connector to fit to 100mm ducting.

Rigid Duct Insulation by Domus Ventilation. Complies with 2010 Building Regulations and NHBC requirements. Reduces heat loss and virtually eliminates the formation of condensation. Insulates ducting passing through cold spaces and in the heated area of a dwelling.

Insulates both the exhaust and intake ducts into the MVHR unit. An installer-friendly solution which can be fitted quickly and reliably without the need for gluing or taping. The interlocking feature and regular external profile provides homeowners with a neat, professional and continuous appearance.

Building Regulations demand: 0.04 W/m. K thermal conductivity at 25mm insulation thickness. Minimum thermal resistance or R-value = 0.025/0.04 = 0.625 K/W. Domus Thermal provides: 0.03 W/m. K thermal conductivity at 20mm insulation thickness. Thermal resistance or R-value = 0.020/0.03 = 0.666 K/W. Insulation Sheet 1m x 1.2m. Foil coated bubble wrap insulation sheet. Round profile tested to the temperature and pressure conditions of BSEN 1363-1: 1999 and the principles of BSEN 1366-3: 2009. Tested with Uncapped/Uncapped (U/U) duct configurations as required for ventilation duct. Suitable for masonry walls or plasterboard partitions. Suitable for insulated and non-insulated partitions. Performance unaffected by weathering (type x durability).

Space needed around duct to fit the fire collar. Prevent the spread of fire.

Tested to BSEN 1366-3: 2009. Suitable for PVC, PVC-U, PE, HDPE, MDPE, PP & ABS pipes. Available for Ø100mm, Ø125mm and Ø150mm ducting. Cowl with Non Return Flap. Designed to help shield the duct from the wind and deflect the air away.

As the appliance operates, the flap lifts to allow exhaust air to disperse to atmosphere. The non return flap acts as an additional measure to help reduce airflow returning through the duct. The flap is free moving and not air tight. Brown Black White Beige Terracotta.

Stainless Cowl with Non Return Flap. Supplied with 4 stainless steel screws & 4 wall plugs. Rubber Seal between cowl and wall. 153 x 153mm square with round spigot.

Gravity Outlet Domus 2 Flap. As the appliance operates, the flaps lift to allow exhaust air to disperse to atmosphere. The flaps close when not in use and act as an additional measure to help reduce airflow returning through the duct, The flaps are free moving and not air tight.

A 100mm round Spigot fits into 100mm ducting. Prefer a Gravity vent with 3 flaps? Gravity Outlet Verplas 3 Flap. As the appliance operates, the flaps lifts to allow exhaust air to disperse to atmosphere. The non return flaps acts as an additional measure to help reduce airflow returning through the duct, they are free moving and not air tight. Supplied with rubber seal between wall and vent. Louvred Grille - (Verplas) with flyscreen. Designed to prevent water ingress and where possible deflect low levels of wind pressure against the fan. Louvres should be installed facing downwards.

The louvred panel is removed to expose the fixing screws. Free Area: Round end: 7,283mm² Max/min temp: 60°C / -15°C Material(s) used: High Impact Polystyrene.

Louvred Grille - (Domus) with flyscreen. Exterior Round louvred grille with flyscreen. Smart vent for venting fan through a soffit or wall. Brown Version has a 25mm long 100mm diameter spigot on the back to attach hose or pipe. White Version has a 39mm long 100mm diameter spigot on the back to attach hose or pipe.

Stainless Bullnose with louvres & fine Mesh. Bull nose design to reduce low levels of wind pressure agains the fan.

Manufactured from Grade: 304 Stainless steel. A vent for use where access is an issue. Free Area: 6499 mm² Max/min temp: 60°C / -15°C Material(s) used: High Impact Polystyrene Recommended core : 115mm Ø. Fitting images show the standard ventilation lapVent, however the exhaust lapVent fits in the same way. The replacement membrane that wraps around the lapVent body needs to be tucked into the felt overlap below the lapvent, so position to allow access for this.

Exhaust LapVent roof vent for extract fan. The lapVent exhaust vent is a quickly installed unit to exhaust extracted air from bathrooms and ensuites. LapVent offers the DIYer a simple installation and construction trades an efficient and quick solution for their customers.

The vent fits in the felt/roofing membrane overlap. There is virtually no disruption, in fact no external work whatsoever when using lapVent, so nothing shows, no unsightly roof vents or risk of breaking tiles.

Cost effective: There is no need to cut core holes through the wall which can require specialist equipment, scaffolding and is time consuming, costly and dusty. Extractors can be easily vented via the loft space. Extracted air is expelled through the body of the vent to atmosphere via the roof batten cavity.

The vent has a unique sloping outlet to prevent condensation dripping back into the system. Insects and pests are denied access through the vent by means of a mesh.

The none load bearing lightweight body of lapVent is shaped to form a weatherproof, unexposed, controlled airway which safely interconnects inside roof voids with atmosphere. Six ramped traps prevent any entry of storm driven rain and snow. Fitting requirements: A minimum gap of 315mm is required between rafters and the roof felt needs to be in good tight condition to prevent blow back.

Tools required: Utility knife to cut the felt, cross headed Screw driver. Appropriate PPE should be used as assessed. DImensions: Vent dimensions: Length: 540mm Width: 315mm Height: 145mm.

Standard award winning lapVents are also available designed to solve roof space condensation and ventilation problems. DIY fit extractor fan roof vent to vent from a bathroom or ensuite. No need to get on the roof or remove a roof tile.

1 x Exhaust Vent 1 x replacement felt/membrane 2 Pre drilled battens 1 x rafter strap 1 x screw pack 1 x 3m 100mm PVC flexible ducting 1 x worm drive Hose clip Fitting Guide. Universal Roof Ventilator Tile (Brown or Grey). The Tile ventilator is manufatured from rigid PVC.

It is suitable for most concreteinterlocking and plain roof tiles with a pitch over 17.5 degrees. It is supplied with adaptors to fit 100mm 125mm and 150mm.

Suitable forhigh and low ventilation and complies with relevant Building Regulations and British standards. Note - Not Suitable for the following profiles: Redland Delta, Cambrian, Saxon, Richmond, Anchor Centurion, Slate, Marley Monarch, Clay Pantiles and Landmark Slates. Colour: White Free Area: 20,000mm² Max/min temp: 60°C / -15°C Material(s) used: PVC Brand: Klober. Manufactured from white epoxy powder coated steel. Fully adjustable and has a locking nut to fix the position of the control disc upon commissioning.

Supplied complete with a fixing body with pre-drilled holes for installation. See our selection of rigid or flexible ducting. Fire Rated White extract Valve.

Message for Fitting guide or fire test report. White Powder coated Supply Valve. Fire Rated White Powder coated Supply Valve. Stainless Exhaust and Supply Valve.

Ceiling diffuser with fixing ring. Colour: White Free Area: 1507mm² with control disc 10mm open Max/min temp: 60°C / -15°C Material(s) used: Polypropylene.

White diffuser with fixing ring. Also available in a chrome finish. Chrome diffuser with fixing ring. Made from white plastic with a chrome finished plastic grille.

PVC Flexible Ducting 100mm diameter. A light weight white PVC Hose used. 1, 3, 6,10, 15 or 45 metre long when fully stretched. Colour: White Free Area: 7,855mm² Max/min temp: 60°C / -15°C Material(s) used: PVCp. Sealing Tape or worm drive clips are available! 6m Aluminium PVC Combi Flexible Ducting. 6 metre Long fully Stretched. Message if you need a 10m. Colour: Black, Silver Free Area: 7,855mm² Max/min temp: 150°C / -30°C Material(s) used: Aluminium, Polyester, PVC.

Don't forget your worm drive hose clips! 10m Insulated Aluminium 100mm diameter. 10m stretched Insulated aluminium flexible hose. Don't forget your hose clips will need to have enough adjustment to allow for the extra thickness of the insulation!

6m Polyester Reinforced PVC Flexible Ducting. Reinforced, highly resilient PVC Flexible hose. Designed to be used for low & medium Pressure heating, ventilation, cooling, and exhaust systems. Manufactured from hard wearing PVC with high tensile steel wire.

Colour: Grey Free Area: 7,855mm² Max/min temp: 150°C / -30°C Material(s) used: PVC Coated Polyester Fibre. Colour: Grey Free Area: 7,850mm² Material(s) used: Aluminium. Hose for this tyoe of hose is available see below. Sealants, Hose Clips and Tape. 100mm Worm Drive Hose Clip.

Worm drive clips with an adjustment between 90 - 110mm. Ideal for attaching flexible hose to ducting fittings.

Hose clip for Semi Rigid Aluminium Ducting 100mm. Hose clips with an adjustment between 90 - 110mm. For securing semi rigid aluminum ducting.

50mm wide for joining ducting fittings together. Available in either 33m or 4.6m rolls. Everbuild 175 Universal Acrylic Sealant. For low movement construction joints, sealing framework and general building uses. For joining and sealing duct together.

The item "4 100mm Plastic Round Ducting Ventilation Tube Extractor Fan Vent Pipe fittings" is in sale since Sunday, November 15, 2015. This item is in the category "Home, Furniture & DIY\Heating, Cooling & Air\Indoor Air Quality & Fans\Extractor Fans". The seller is "sentdirect2u" and is located in Swanage, Dorset. This item can be shipped to United Kingdom, Antigua and barbuda, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Brazil, Japan, China, Israel, Hong Kong, Norway, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Belize, Bermuda, Bolivia, Barbados, Brunei darussalam, Cayman islands, Dominica, Ecuador, Egypt, Guernsey, Gibraltar, Guadeloupe, Grenada, French guiana, Iceland, Jersey, Jordan, Cambodia, Saint kitts and nevis, Saint lucia, Liechtenstein, Sri lanka, Macao, Monaco, Maldives, Montserrat, Martinique, Nicaragua, Oman, Pakistan, Peru, Paraguay, Reunion, Turks and caicos islands, Aruba, Saudi arabia, South africa, United arab emirates, Chile, Bahamas, Colombia, Costa rica, Dominican republic, Kuwait, Panama, Philippines, Qatar, Uruguay, Viet nam.

• Non-Domestic Product: No
• Type: Extractor Fans
• Modified Item: No
• Country/Region of Manufacture: United Kingdom
• Custom Bundle: No
• MPN: Does Not Apply
• Brand: Verplas / Domus